One-piece toilet
WP-5004 is a floor-mounted ceramic toilet with a one-piece body. The bowl and cistern body are combined, so the order does not involve matching a separate close-coupled tank to the pan. The cistern cover, seat and internal fittings remain service parts. That distinction matters when comparing the complete fixture with a bare pan or a wall-hung bowl that needs a separate concealed cistern.
The specified flush type is washdown. The model description identifies a control with two flush selections; the operating volume depends on the fitted mechanism and its setting. The proposed assembly carries its full and reduced volume information and any documentation required for the destination. The control format alone is not an efficiency certification.
We confirm A UF cover with the ceramic toilet. For a project order, the seat profile and hinge fit should remain tied to WP-5004 so replacement parts fit the same bowl. Cover removal provides access for cleaning, but the release method follows the supplied hinge.
The 250 mm S-trap is one of the listed WP-5004 connections. An S-trap arrangement serves a floor outlet, so the choice starts with the building waste position and the proposed pan connection. The 250 mm label stays attached to this version in the quotation. The matching installation drawing supplies the measurement points and connector arrangement for the room.
The 300 mm S-trap is a separate listed selection for a floor-outlet layout. It should not be substituted for the 250 mm version simply because the ceramic body looks similar. The two S-trap entries remain separate in the room schedule, so each bathroom receives the version intended for its waste position.
The 180 mm P-trap selection uses a wall-outlet arrangement. It is intended for a different waste route from the two S-trap selections. The wall connection, coupling and installation access need to suit that version. Selecting P-trap in the inquiry carries the 180 mm model label into the request without treating the floor and wall connections as interchangeable.
| Model & body | WP-5004; one-piece ceramic toilet; floor-mounted installation. |
|---|---|
| Selected trap configuration | S-trap: 250 mm listed connection |
| Listed overall size | 730 × 335 × 720 mm. Bowl, seat, fixing and connection dimensions belong to the fixture installation drawing. |
| Flush configuration | Washdown flush. A control with two flush selections is described for the model; actual flush volumes and required destination documentation are identified with the proposed flushing assembly. |
| Seat & cover | UF cover specified with the ceramic fixture. Seat profile, hinge fit and replacement-part reference matched to the ordered toilet. |
| Connection choices | Listed S-trap options: 250 mm or 300 mm; listed P-trap option: 180 mm. Outlet fitting, measurement points and installation clearances follow the matching model drawing. |
| Supply & installation | Water inlet position, thread, valve access, connector, seals and fixing components identified for the chosen version; local plumbing and installation quoted as site work. |
| Minimum order | Quoted per model at your project quantity. Where a factory model has a production minimum, the quotation states it; small quantities can ship with the rest of your project in one container. |
| Standards & certificates | Matched to the ordered model: tell us the standards or certificates your market or project requires, and we confirm in writing which documents are available for this configuration before you order. |
Open product drawing ↗
Start the fixture schedule from the waste route: floor for an S-trap layout, wall for a P-trap layout. The listed 250, 300 and 180 mm values identify the WP-5004 version, and its drawing must use the same measurement points as the site survey. An offset connector is an extra component, used only where the drawing shows it fits.
The cistern needs a water supply matched to its inlet fitting, with inlet position, connection thread and access to the isolation valve planned along with the waste trap. Leave space to lift the cistern cover and service its fittings. Supply hoses, valves and any pipe relocation are installation items.
WP-5004 has a listed overall size of 730 × 335 × 720 mm. The bathroom layout still needs the bowl and seat dimensions, movement space beside and in front of the fixture, and a clear door swing. For an accessible or height-specific bathroom brief, the actual fixture dimensions and applicable project requirements must be matched before selection.
The product subtotal identifies WP-5004, the selected S-trap 250 mm, S-trap 300 mm or P-trap 180 mm version, the finish and quantity. A multiroom order can group units by connection type and delivery stage. Keeping those groups explicit prevents a single toilet quantity from hiding several different installation requirements.
The component list names the matched seat and UF cover, hinge arrangement, flush mechanism and inlet fittings, with spare seats, hinges or valves as extra lines. That keeps the ceramic fixture and its service parts together as one defined package, with replacement quantities planned for the project.
The selected waste connector, seals and fixing hardware need their own supply entries. Site preparation, water-feed alterations, drain changes and installation labor are separate tasks. For replacement projects, removal of the old fixture and disposal can be priced alongside installation.
The ceramic body, cistern cover and seat need protection against movement and contact during transport. Packing and shipment quantities are listed for the actual order, with any spare units separated from installation quantities. Freight uses the packed dimensions and destination; unloading, stairs or lifting and delivery to individual bathrooms are distinct charges when required. Tell us the rooms and quantities and we will put this on one quote with everything else you are ordering, and show you what fits in a container.
The listed choices are S-trap 250 mm, S-trap 300 mm and P-trap 180 mm. S-trap is for a floor-outlet arrangement; P-trap is for a wall-outlet arrangement. The selected version needs a matching installation drawing and connector, with the measurement points checked against the room.
No. Twelve inches is 304.8 mm, while this model lists 300 mm. Compatibility depends on the actual pan drawing, connector and installation tolerances. The order should retain the WP-5004 connection label and be matched to the measured site layout.
We confirm A UF cover with the WP-5004 ceramic fixture. The quotation should name the matched seat, cover and hinge set so the supplied components and future replacements remain clear. Soft-close action or a particular quick-release mechanism is a separate feature.
The WP-5004 is a washdown toilet with a dual full and reduced flush. We confirm both flush volumes for the flush assembly fitted to your order, so you can check them against your local water-efficiency rules before you approve the sample.
No. The listed overall size is 730 × 335 × 720 mm. Seat height, bowl dimensions, fixing points and the space needed around the toilet are separate. The bathroom plan needs the actual fixture drawing, door swing and required user clearances, especially where a specific accessible layout is part of the brief.
It should identify the selected trap version, matched seat and cover, flush and inlet fittings, and any supplied connector, seals or fixing hardware. Spares, packing and freight are separate entries. Local plumbing changes, installation, removal of old fixtures and final-room delivery are included only where they are expressly listed.
Wall-Hung Ceramic Toilets with Soft-Close Covers
Two-Piece Ceramic Toilet with a Separate Tank and Bowl
WP-2030 Washdown Two-Piece Toilet
U5 Instant-Heating Smart Toilets