Satin Silver
Satin-silver anodized aluminum is the default. The groove crests and exposed front return share the selected finish reference.
Flush Aluminum Stair Nosing for 10 mm Floor Finishes
Flush Aluminum Stair Nosing for 10 mm Floor Finishes
- Selected material
- 6063-T5 aluminum; nominal 2.5 mm metal wall
- Stair nosing finish
- Satin-silver anodized aluminum
- Selected finish build-up
- 10 mm from mounting-leg top to finished tread top
Flush Stair Tread Face and Underfloor Mounting Leg
55 mm Grooved Tread Face
The selected aluminum tread face is 55 mm deep, with longitudinal grooves across its upper walking surface. It meets the adjacent finish at the same top plane. The grooves are a surface detail.
10 mm Finish Interface
The selected 10 mm build-up is measured from the upper surface of the rear mounting leg to the finished tread top. The mounting leg projects 15 mm behind the tread face, providing a defined interface beneath the adjoining finish.
25 mm Front Return
The front return drops 25 mm from the finished tread top. The selected nominal metal wall is 2.5 mm, with 6063-T5 aluminum and 2700 mm straight bars specified for this profile.
Aluminum Stair Nosing Finishes
Champagne
The champagne-anodized option uses the same selected section and 2700 mm bar length. A warm metallic tone can be coordinated with adjacent handrails and floor trim.
Black
The black powder-coated option retains the selected geometry. Color, sheen and protection of exposed cut ends form part of the finish schedule.
Selected Flush Stair Nosing Section
| Selected material | 6063-T5 aluminum; nominal 2.5 mm metal wall |
|---|---|
| Selected nosing finish | Satin-silver anodized aluminum |
| Selected tread face | 55 mm front-to-back |
| Selected finish build-up | 10 mm from mounting-leg top to finished tread top |
| Selected front return | 25 mm down from finished tread top |
| Selected rear mounting leg | 15 mm projection behind the tread face |
| Selected bar length | 2700 mm |
| Assembly boundary | Flush edge detail; support, fixing and slip requirements coordinated with the stair design |
| Standards & certificates | Matched to the ordered model: tell us the standards or certificates your market or project requires, and we confirm in writing which documents are available for this configuration before you order. |
Open product drawing ↗
Floor Build-Up, Tread Edge and Bar Cuts
Match the Full Floor Assembly
Include adhesive or bedding above the mounting leg, the substrate level and the required finished tread plane in the section detail.
Measure the Stair Edge by Run
Schedule the clear width of each stair edge, exposed side returns and any joint locations. The selected 2700 mm bar length is divided into those runs, plus a cutting allowance.
Coordinate Fixing and Edge Support
The nosing, substrate edge, rear leg and adjoining finish need a continuous coordinated support detail. Fixings, adhesive, movement provisions and any required slip testing are project-specific items.
Stair Nosing Supply and Quote
Section and Bar Quantity
Quote the 55 mm tread face, 10 mm finish interface, 25 mm return, 15 mm rear leg and 2.5 mm nominal wall with the required bar count.
Finish and Cut Treatment
List satin silver, champagne or black and identify exposed cut ends. Keep finish samples and any cut-end treatment on the same stair reference.
Cut List and Stair Labels
Separate full bars from any requested cut-to-length work. Tie each cut length, joint and end detail to the stair and tread location.
Fixing Materials and Packing
Itemize any requested mounting materials, protective packing and destination. Floor finishes, substrate preparation and installation labor are outside the profile line item.
Flush Stair Nosing Schedule
- Section
- Selected dimensions, floor build-up and material
- Quantity
- Stair references, runs, joints and bar/cut count
- Finish
- Surface sample and exposed-end treatment
- Outside supply
- Fixing materials, packing and destination
Flush Aluminum Stair Nosing Questions
What does the 10 mm dimension describe?
It is the selected distance from the upper surface of the rear mounting leg to the finished tread top. The adjacent finish and its bedding must fit that interface.
How wide is the stair nosing face?
The selected grooved tread face is 55 mm deep from the front edge to its rear edge. A separate mounting leg projects 15 mm farther behind the tread face.
How is the 25 mm return measured?
It is the vertical drop from the finished tread top to the bottom of the front return. The selected nominal aluminum wall is 2.5 mm.
Do the grooves make the stair edge slip-resistant?
Yes. The grooved profile adds grip at the stair edge, where most slips happen. For commercial stairs we can supply versions with anti-slip inserts and the slip test report your project requires.
Which finishes and bar length are selected?
Satin-silver anodized, champagne anodized and black powder-coated aluminum are selected on the same section. Straight-bar length is 2700 mm.
What should a stair-nosing request include?
Include a tread section, full finish build-up, substrate edge detail, stair widths, joints, finish and destination. Add any requested cutting, mounting materials and exposed-end treatment as their own items.
More Floor Trim & Accessories
Aluminum Reducer Strips for Unequal Floor Levels
Ceramic Cove Base Tile with a Concave Floor Return
Aluminum Floor Movement-Joint Profiles with a Flexible Insert
35 mm Aluminum T-Molding for Same-Level Floor TransitionsRequest a Flush Stair Nosing Quote
Flush Aluminum Stair Nosing for 10 mm Floor FinishesSatin silver