Roller shades at a sliding door
The selected door treatment uses two independently operated roller units. Each unit has a 1500 mm overall bracket-to-bracket width and a 2400 mm finished fabric drop. Independent operation lets the active-door side be raised while the other sheet remains down. These dimensions define the selected assembly, and the size range of the system is confirmed on the quote.
The selected sheet is plain white 100% polyester light-filtering fabric. Its quoted reference establishes the actual hand and translucency. It is an unperforated textile selection without a specified solar-screen openness factor, blackout percentage or thermal rating.
A tensioned spring roller raises and lowers the sheet by direct movement of the bottom bar, with no hanging operating loop or motor. The selected build uses a 44 mm outside-diameter aluminum roller tube with 0.9 mm wall, an aluminum fascia and a weighted aluminum hem bar. The roller mechanism is qualified with the selected sheet and drop as one assembly.
Plain white fabric and a white-finished aluminum fascia form the base appearance. The fabric sample identifies its actual surface and translucency. A darker fabric, textured textile or blackout coating changes the selected sheet and may also change spring balancing.
The selected light-filtering sheet softens daylight through the fabric. Coverage also depends on roller deductions and side or center gaps. The purchase specification identifies the required fabric reference and actual coverage.
The selected fascia covers the upper roller from the room side, and the weighted hem bar keeps the lower edge straight. The fabric rolls forward where needed to clear door handles. Fascia projection and the raised-roll envelope are checked against the actual frame, ceiling and available headroom.
| Custom shade type | Two independent manual cordless spring roller units for the sliding-door opening |
|---|---|
| Shade selection | Selected pair of independent cordless spring rollers, each 1500 mm overall width × 2400 mm drop, white polyester light-filtering fabric, aluminum fascia and hem bar |
| Fabric & light control | White 100% polyester light-filtering fabric; openness and light control confirmed on the approved fabric sample |
| Unit dimensions | Each unit: 1500 mm overall bracket-to-bracket width × 2400 mm finished fabric drop; fabric width deducts the selected hardware |
| Door interfaces | Door frame and handles, sliding-leaf access, raised-shade position, coverage and available upper space |
| Assembly & operation | 44 mm OD × 0.9 mm wall aluminum roller tube; balanced spring mechanism, aluminum fascia, weighted aluminum hem bar and mounting brackets; no motor or operating loop |
| Supply & site work | Shade units and named operating/mounting parts, packing and delivery itemized; measurement, substrate preparation, wiring and installation each stated |
| Minimum order | Quoted per model at your project quantity. Where a factory model has a production minimum, the quotation states it; small quantities can ship with the rest of your project in one container. |
| Standards & certificates | Matched to the ordered model: tell us the standards or certificates your market or project requires, and we confirm in writing which documents are available for this configuration before you order. |
Open roller-shade specification diagram ↗
The selected pair uses two 1500 mm overall units with a 2400 mm fabric drop. Bracket-to-bracket width differs from sheet width because the spring and idler occupy space at the ends. Final unit positions and deductions are coordinated with the active sliding leaf, handles and acceptable center gap.
A full-width shade crosses the complete opening when lowered. Divided units can serve an active door leaf and adjoining fixed glass independently, though they add another edge and mounting position. The selected system sets the permitted unit widths and raised position; the layout keeps handles and the access route clear.
The selected assembly defines mounting surfaces, brackets and operating components. The project identifies any electrical requirements and documentation for that actual system. Substrate preparation, wiring and installation labor are each itemized next to the shade supply.
Our quote identifies the white polyester light-filtering fabric against the selected sheet requirement. A blackout, screen or different textile changes fabric cost and the spring-balancing check.
The selected package contains two independent 1500 × 2400 mm roller units. Fabric width is derived from the actual end hardware and is narrower than the overall unit width.
The base assembly includes spring rollers, 44 mm aluminum tubes, fascia, weighted hem bars and mounting brackets. Electric motors, controllers, wiring and side channels are separate changes to this manual package.
Packing and freight follow the selected units, components and destination. Measurement, unloading, support preparation, installation and electrical work each have an assigned responsibility, and the quote lists exactly what is included. Tell us the rooms and quantities and we will put this on one quote with everything else you are ordering, and show you what fits in a container.
The selected package is a pair of independent roller shades, each 1500 mm overall width and 2400 mm fabric drop. Other openings can use revised custom dimensions, with tube stiffness, spring capacity and fabric weight qualified for that assembly.
No. The selected configuration has two independent units in place of one full-width sheet, and each is raised on its own around the active door leaf. Overall unit width includes its end hardware, so actual sheet coverage and the center gap are recorded in the mounting layout.
The selected package is a manual cordless spring roller operated at its hem bar. It has no hanging control loop and no motor. A chain or motorized arrangement is a separate system selection, with its own mounting and operating requirements.
The base fabric requirement is white 100% polyester light-filtering textile. A blackout or solar-screen fabric is a different selection. The actual fabric reference and sample establish translucency; the selected package carries no numerical blackout, UV or thermal rating.
The selected two-unit arrangement allows the active door side to be raised on its own. Forward fabric roll can clear projecting handles, while the fascia and parked roll need enough headroom. Unit position and the full travel are checked against the actual door and handle geometry.
Provide the opening width and height, door-frame and handle arrangement, available mounting surfaces and upper space, preferred light control and delivery location. Our quote identifies finished shade sizes, the selected operating system, named hardware and site responsibilities.
Side-Gliding Cellular Shades for Sliding Glass Doors
Cordless Roman Shades with Sewn Batten Pockets
Wand-Operated Vertical Blinds for Sliding Glass Doors
Cordless Aluminum Venetian Blinds with Tilt Wands