Three-mode panel
The custom panel is a brushed 304 stainless steel enclosure, 1200 mm high and 220 mm wide, projecting 110 mm from the finished wall, with an integral overhead hood reaching up to 400 mm. It is built on the GEORGE D-070 family's material and mounting design, to these made-to-order dimensions.
Three separate controls set water temperature, flow and outlet mode. The mixer is manually adjusted; thermostatic regulation and an anti-scald certification are not part of this selection. The mode selector supplies one outlet group at a time, so the overhead spray and hand shower do not operate simultaneously.
The two-mode package includes the integral overhead spray and one hand shower with a 1500 mm hose and wall-side holder. The three-mode package adds two perforated body-spray zones in the panel face. Those two zones work together as the third mode; a three-position selector replaces the two-position selector. Both packages keep the same enclosure dimensions.
The enclosure is brushed 304 stainless steel with folded sides. Valve bodies, cartridges, hose and connection fittings each have their own material listed, and the approved surface sample sets brush direction and tone for repeat orders.
The overhead spray is formed within the projecting hood, keeping it aligned with the 220 mm-wide panel. The selected overhead face is 220 × 250 mm. Each package includes one hand shower, one 1500 mm hose and one holder. Replacement handset or hose purchases retain the supplied fitting and thread reference.
The added body-spray package uses two 100 × 180 mm perforated zones centered 1000 mm and 1700 mm above the finished floor. Both zones are supplied by one selector position. Their spray pattern and flow need the selected assembly’s operating information.
| Reference & selected construction | GEORGE D-070 family material/mounting reference; selected custom brushed 304 stainless wall panel. No factory D-070 dimensional or outlet-version mapping is asserted. |
|---|---|
| Outlet package | Same selected panel size and manual controls, adding two perforated body-spray zones and a three-position selector; the two body zones operate together as one mode. |
| Panel & hood dimensions | Selected enclosure H1200 × W220 mm; body projection 110 mm; overhead maximum projection 400 mm; overhead spray face 220 × 250 mm. |
| Mounting setout | Panel bottom 850 mm and top 2050 mm above finished floor. Control centers: mixer 1200 mm, flow 1325 mm, mode selector 1450 mm. Holder center 1500 mm. Bracket/anchor pattern follows the approved assembly. |
| Supplied outlets & controls | Overhead spray + 1 hand shower + 1500 mm hose + holder; manual temperature mixer, separate flow control and 2-position selector. Body-spray option adds two zones and a 3-position selector, one mode at a time. |
| Body-spray option | Two 100 × 180 mm perforated zones centered at 1000 and 1700 mm above finished floor; both operate together in the third mode. |
| Water interfaces & qualification | Selected rear hot/cold inlet requirement: G1/2 parallel connections, 150 mm centers at 1000 mm above finished floor; hot left when facing panel. Matching valves/fittings and pressure/flow curves required for the assembly; no universal operating-pressure rating asserted. |
| Minimum order | Quoted per model at your project quantity. Where a factory model has a production minimum, the quotation states it; small quantities can ship with the rest of your project in one container. |
| Standards & certificates | Matched to the ordered model: tell us the standards or certificates your market or project requires, and we confirm in writing which documents are available for this configuration before you order. |
Open panel setout drawing ↗
The selected setout places the 1200 mm panel between 850 and 2050 mm above the finished floor. Mixer, flow and mode controls sit at 1200, 1325 and 1450 mm respectively. The holder center is 1500 mm. These are the custom layout dimensions; user reach, shower screens and the room’s accessibility requirements are checked against this arrangement.
The selected connection layout uses rear hot and cold G1/2 parallel inlets at 150 mm centers, both 1000 mm above the finished floor, with hot on the left when facing the panel. Matching connectors and sealing arrangements are included in the component submittal. Existing pipework can remain only if its position, thread, pressure and flow suit the approved assembly.
The enclosure occupies 110 mm in front of the finished wall, while the overhead hood reaches 400 mm. The supplied support rails, brackets and substrate-appropriate anchors must carry the complete panel without relying on tile alone. Fixing positions and rear service removal follow the approved component layout; penetrations retain the wall waterproofing detail.
The base package includes the overhead spray, hand shower, hose, holder, manual mixer, flow control and two-position selector. The body-spray package adds two perforated zones and the three-position selector. The same enclosure size and brushed finish allow the extra water outlets and valve arrangement to be compared directly.
The quotation includes the panel, support rails or brackets, named control cartridges, hose and holder, rear connectors and component list, with site-specific anchors, inlet shutoffs and extra adapters as their own lines. A like-for-like replacement keeps the same outlet groups, inlet setout and control references.
Site work covers removal of existing fittings where required, preparation of suitable support, water connections and panel installation. Pipe alterations, waterproofing and tile repairs depend on the bathroom condition. These works are separate from the panel subtotal. Surface mounting changes the installation arrangement.
Packing protects the panel face and keeps small fittings apart from it, with room or package references keeping each panel and its connection parts together in delivery and site storage. Packing, freight, unloading and final delivery are set for the actual order and destination. Tell us the rooms and quantities and we will put this on one quote with everything else you are ordering, and show you what fits in a container.
The custom enclosure is 1200 mm high × 220 mm wide, with 110 mm body projection and 400 mm maximum overhead reach. Its bottom is set at 850 mm and top at 2050 mm above the finished floor. These are made-to-order dimensions for this enclosure, confirmed on the approval drawing.
The selected requirement is two rear G1/2 parallel connections at 150 mm centers and 1000 mm above the finished floor, hot on the left when facing the panel. Existing supplies must also match the approved assembly’s pressure, flow and sealing arrangement.
The panel enclosure is 304 stainless steel, and the valves, cartridges, hose, handset and connection fittings each have their own specified materials and references.
Two 100 × 180 mm perforated body-spray zones are added to the panel face, centered at 1000 and 1700 mm above the floor. A three-position selector replaces the two-position selector. The two zones operate together as one mode, while the enclosure, overhead spray, hand shower and mounting heights remain the same.
The mode selector runs one group at a time: overhead, hand shower, or the paired body zones in the three-mode package. Temperature is mixed manually and flow has its own control; for thermostatic mixing or several outlets at once, we would specify a thermostatic panel.
Order approval needs the dimensioned enclosure and inlet setout, support and bracket layout, mixer and selector references, hose and handset fittings and pressure and flow information, all matched to the two- or three-mode configuration and the site supplies. Substrate anchors, waterproofing, pipe alterations and installation are site work.
8018 Push-Button Thermostatic Shower Set
Hand Shower Slide-Bar Kits with Adjustable Holders
Adjustable Shower Body-Spray Jet Sets
Concealed Shower Systems with Rain & Waterfall Outlets